RIB winterisation: checklist and tips
Preparing your RIB for winter storage properly protects the tubes, hull, engine and equipment during a long period of storage. Salt, damp, temperature changes and UV rays can speed up the ageing of materials if the boat is not properly cleaned and protected.
Before laying up your RIB for the winter, a few jobs are essential: emptying the boat, cleaning and drying the surfaces, preparing the engine and battery, then choosing a suitable storage place.
Here are the steps to follow to prepare your inflatable boat for winter and make it easier to recommission when the good weather returns.
Checklist: preparing your RIB for winter

Before you start, use this list to organise the main jobs:
- Remove equipment and personal belongings from the boat.
- Clean the tubes, hull, deck and accessories.
- Dry the boat completely to limit mould.
- Clean and store the upholstery and removable equipment.
- Prepare the engine according to the manufacturer's recommendations.
- Check and maintain the battery according to its instructions.
- Inspect the tubes, valves, fittings and any damaged areas.
- Choose a dry, stable, sheltered and well-ventilated place.
- Fit suitable protection without trapping moisture.
1. Empty the boat and take stock of the equipment
The first step in winter storage is to remove removable items and equipment. This makes cleaning easier, avoids leaving belongings on board for several months and reduces the risk of damage when moving or handling the boat.
Take the opportunity to list your equipment and check its condition before next season.
- Navigation equipment: GPS, VHF and other removable devices should be stored or protected according to their manufacturer's recommendations.
- Leisure gear: masks, fins, snorkels, wakeboards, fishing rods and accessories should be rinsed if necessary, dried and put away.
- Safety equipment: check the life jackets, buoys, fire extinguishers and flares. Follow the storage conditions and expiry dates specific to each item.
- Personal belongings: remove clothes, towels, food and anything else that could hold moisture or deteriorate during storage.
Putting things away is also a chance to spot worn or missing equipment so you can replace it before you go out again. See our guide to the safety equipment needed on board a RIB.
2. Clean the tubes, hull and deck
A thorough clean before storage helps limit the build-up of salt, dirt and deposits that could mark the surfaces. It also makes it easier to inspect the parts exposed to rubbing and weather during the season.
Cleaning the inflatable tubes
Rinse the tubes with fresh water to remove salt and surface dirt. Then use a product compatible with the tube material, whether PVC or CSM/neoprene, commonly known as Hypalon.
A suitable product and a sponge or soft brush let you clean the surfaces without damaging them. Rinse if necessary, then let the tubes dry completely before covering the boat.
There is generally no need to remove the tubes for routine cleaning. If removing them is essential for a specific job, check the manufacturer's procedure or call in a professional.
Find our tips for cleaning and maintaining a RIB, as well as our range of boat cleaning products.
Cleaning the hull and deck
Rinse the hull and deck with fresh water, then use a cleaner suited to the material and finish of the surfaces. A GRP hull, an aluminium hull and a teak deck may need different methods and products.
Avoid acidic or strongly alkaline products unless their compatibility is confirmed. Also protect electrical and electronic equipment from splashes.
Antifouling is not a routine part of winter storage. Whether it is useful depends on the type of hull, any existing coating and how the boat is used or stored. If you are considering applying it, check the recommendations of the hull and coating manufacturers.
3. Prepare the upholstery, equipment and battery
Cleaning and storing the upholstery
Seats, cushions, covers and other upholstery can hold moisture, especially when made of textiles or foam. Clean them with compatible products, then let them dry completely before storing them in a dry place.
Where possible, remove the removable parts and store them away from rain, condensation and large temperature changes. Do not put cushions away in a closed locker while they are still damp.
To limit the risk of mould on the tubes and equipment, also see our article on preventing mould and fungus on inflatable boats.
Checking and maintaining the battery
The battery must be prepared for a period of inactivity according to its manufacturer's instructions. Where the boat's layout allows, removing it and storing it in a dry, cool, frost-free place may be recommended.
Before storage, check its condition and charge, and clean the terminals if necessary, following the safety instructions. A battery left discharged for a long time may deteriorate.
How often to check it and how to recharge it depend on the type of battery, its condition and its charging system. Check its instructions: periodic recharging or a suitable maintenance charger may be needed during the winter.
4. Prepare the engine for winter
Winterising the engine is an essential step. The jobs vary according to the make, model, type of engine and planned storage period. The procedures for an outboard are not necessarily the same as those for an inboard.
To avoid damaging the engine, follow the manufacturer's manual first and foremost. If in doubt, or if you do not have the necessary equipment, leave this job to a marine maintenance professional.
Flushing the engine and protecting the cooling system
After use in salt water, flushing with fresh water limits salt build-up and the risk of corrosion. The flushing method, however, depends on the engine model and the system provided by its manufacturer.
If the boat is stored in an area exposed to frost, the cooling system and any other circuits containing water must be prepared according to the manufacturer's instructions. Incomplete draining or the wrong procedure can cause damage.
Checking lubricants, fuel and filters
Depending on the model and the service schedule, winter preparation may include changing the engine oil, some filters and the gearbox oil, as well as inspecting various components.
Preparing the fuel system must also follow the manufacturer's procedure. Depending on the engine and its fuel system, it may involve a suitable stabiliser, renewing the fuel or other steps. Do not routinely drain the tank without checking the recommendations for your installation.
Inspecting exposed parts
Use the winter lay-up to look for signs of wear or corrosion. Depending on the engine, the checks may include:
- The propeller and its shaft, looking for damage and debris.
- The sacrificial anodes and how worn they are.
- Spark plugs, filters and the other items in the service schedule.
- Grease points, joints and controls.
- Any leaks and unusual signs of corrosion.
Oil change and replacement intervals are not universal: they depend on the engine and how it is used. Check the manual rather than applying the same interval to every engine.
5. Inspect the tubes and carry out any repairs needed
Once the boat is clean and dry, examine the inflatable tubes carefully. Cleaning makes it easier to spot small areas of damage that may have gone unnoticed during the season.
Check in particular for:
- Signs of abrasion, cracks or unusual discolouration.
- The condition of the valves and the areas around fittings.
- Signs of seams lifting where the joins are accessible.
- Loss of pressure or damage that needs a diagnosis.
If you find a leak, a tear or a seam lifting, have the repair assessed before the next launch. Small repairs can sometimes be done without a complete replacement, while more serious damage needs a specialist.
ORCA Retail offers ORCA technical fabrics for repairing tubes. The material, glue and repair method must be compatible with the original fabric and the type of damage.
6. Choose a suitable place and protection
Where you store the boat has a direct effect on how well it survives the winter. As far as possible, choose a dry, stable place sheltered from the weather, with enough air circulation.
In particular, your boat should be protected from:
- Prolonged exposure to UV rays.
- Rain, condensation and standing moisture.
- Frost when the climate requires it.
- Dust, dirt and outside pollution.
- Knocks and loads that could deform or damage the tubes.
Storing the boat in good conditions
If the boat is kept on its trailer or on a cradle, make sure the whole set-up is stable and the support points are suitable. Avoid loads that could crush the tubes, and check that water cannot collect on the hull or the cover.
Tube pressure and engine position during storage must follow the manufacturer's recommendations. There is no need to remove the tubes or deflate them completely every winter.
Fitting a winter cover
A suitable cover protects the RIB from the weather and dirt. It must be properly supported and fitted to avoid pockets of water, while still allowing enough ventilation.
Before covering the boat, check that the tubes, upholstery and lockers are dry. A waterproof cover put over a damp boat can encourage condensation and mould.
To choose the most suitable protection, see our guide to covers and protective covers for RIBs.
Using a professional for winter storage
If you do not have the necessary equipment, or if your engine needs specific work, a professional can take care of servicing and preparing the boat for storage.
They can check the mechanical parts, carry out the work specified by the manufacturer and look for any damage to the tubes or hull.
See our network of RIB repairers to find a professional who can help you.
FAQ: winter storage for a RIB
When should you prepare your boat for winter?
Prepare the boat before a long period of storage, ideally as soon as the season ends. Don't wait for the first frosts to do the necessary jobs, especially on the engine and any circuits that may contain water.
Should you deflate the tubes to store a RIB for winter?
Not necessarily. The recommended pressure during storage depends on the boat's design and its manufacturer's instructions. Follow these rather than fully deflating the tubes by default.
How do you avoid mould over the winter?
Clean and dry the boat completely before covering it. Store damp upholstery separately until it is dry, let air circulate under the cover and regularly check lockers and poorly ventilated areas.
Should you change the engine oil before winter storage?
What needs doing depends on the type of engine and its manufacturer's service schedule. Changing some lubricants or filters may be recommended, but you should not apply one universal procedure to every engine. Check the manual or ask a professional.
Can you leave your RIB outside over the winter?
Outdoor storage is possible if the boat is on a suitable support and protected by an appropriate cover. You do, however, need to limit the build-up of water, snow or dirt and keep enough ventilation under the cover. A dry shelter is still better where possible.
ORCA products for winter storage
- New Magic degreasing cleaner: also use it before any gluing
- Shmuffex mould remover: against black spots and fungus
- Gumemp100 protective wax: protects the tubes from UV
- CEREDI pressure relief valve: prevents over-pressure when the tube heats up in the sun
- Neoprene glue + hardener kit: everything you need to glue a patch onto Hypalon
Get your RIB ready for next season with ORCA Retail
Successful winter storage comes down to a few simple principles: clean the boat, dry the surfaces, prepare the engine and battery according to the manufacturers' recommendations, inspect the tubes and choose suitable protection for storage.
ORCA Retail offers cleaning products for inflatable boats as well as technical fabrics for repairing tubes.
To go further, see our tips for maintaining your RIB and preparing it for relaunch after the winter.